KVR26N19S8/8
|
ValueRAM, Kingston’s industry-standard memory, delivers award-winning performance and legendary Kingston reliability. When you know what you want, you want ValueRAM. |
|
|
|
8GB Module – DDR4 – 2666MHz
- Part Number: KVR26N19S8/8
- Specs: DDR4, 2666MHz, Non-ECC, CL19, 1.2V, Unbuffered, DIMM, 1R, 8Gbit
|
|
DESCRIPTION
This document describes ValueRAM’s KVR26N19S8/8 is a 1G x 64-bit
(8GB) DDR4-2666 CL19 SDRAM (Synchronous DRAM), 1Rx8,
memory module, based on eight 1G x 8-bit FBGA components. The
SPD is programmed to JEDEC standard latency DDR4-2666 timing of
19-19-19 at 1.2V. Each 288-pin DIMM uses gold contact fingers. The
electrical and mechanical specifications are as follows:
FEATURES
- Power Supply: VDD=1.2V Typical
- VDDQ = 1.2V Typical
- VPP – 2.5V Typical
- VDDSPD=2.2V to 3.6V
- Nominal and dynamic on-die termination (ODT) for
data, strobe, and mask signals
- Low-power auto self refresh (LPASR)
- Data bus inversion (DBI) for data bus
- On-die VREFDQ generation and calibration
- Single-rank
- On-board I2 serial presence-detect (SPD) EEPROM
- 16 internal banks; 4 groups of 4 banks each
- Fixed burst chop (BC) of 4 and burst length (BL) of 8
via the mode register set (MRS)
- Selectable BC4 or BL8 on-the-fly (OTF)
- Fly-by topology
- Terminated control command and address bus
- PCB: Height 1.23” (31.25mm)
- RoHS Compliant and Halogen-Free
|
 |
KVR26N19S8/8
8GB 1Rx8 1G x 64-Bit PC4-2666Mhz
CL19 288-Pin DIMM
Important Information: The module defined in this data sheet is one of several configurations available under this part number. While all configurations are compatible, the DRAM combination and/or the module height may vary from what is described here. |
Specifications
KVR26N19S8/8
8GB 1Rx8 1G x 64-Bit PC4-2666Mhz
CL19 288-Pin DIMM
DESCRIPTION
This document describes ValueRAM’s KVR26N19S8/8 is a 1G x 64-bit
(8GB) DDR4-2666 CL19 SDRAM (Synchronous DRAM), 1Rx8,
memory module, based on eight 1G x 8-bit FBGA components. The
SPD is programmed to JEDEC standard latency DDR4-2666 timing of
19-19-19 at 1.2V. Each 288-pin DIMM uses gold contact fingers. The
electrical and mechanical specifications are as follows:
FEATURES
- Power Supply: VDD=1.2V Typical
- VDDQ = 1.2V Typical
- VPP – 2.5V Typical
- VDDSPD=2.2V to 3.6V
- Nominal and dynamic on-die termination (ODT) for
data, strobe, and mask signals
- Low-power auto self refresh (LPASR)
- Data bus inversion (DBI) for data bus
- On-die VREFDQ generation and calibration
- Single-rank
- On-board I2 serial presence-detect (SPD) EEPROM
- 16 internal banks; 4 groups of 4 banks each
- Fixed burst chop (BC) of 4 and burst length (BL) of 8
via the mode register set (MRS)
- Selectable BC4 or BL8 on-the-fly (OTF)
- Fly-by topology
- Terminated control command and address bus
- PCB: Height 1.23” (31.25mm)
- RoHS Compliant and Halogen-Free
|
SPECIFICATIONS
CL(IDD) |
19 cycles |
Row Cycle Time (tRCmin) |
45.75ns (min.) |
Refresh to Active/Refresh
Command Time (tRFCmin) |
350ns (min.) |
Row Active Time (tRASmin) |
32ns (min.) |
Maximum Operating Power |
(1.2V) = TBD W* |
UL Rating |
94 V – 0 |
Operating Temperature |
0o C to 85o C |
Storage Temperature |
-55o C to +100o C |
|
Important Information: The module defined in this data sheet is one of several configurations available under this part number. While all configurations are compatible, the DRAM combination and/or the module height may vary from what is described here. |
Reviews
There are no reviews yet.